MULTI-TECH SYSTEMS, INC.

MT5634ZLX/E, MT5634ZLX/E-T/2

Card Type

Modem

Chip Set

Unidentified

Maximum Modem Rate

56Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103/212A

ITU-T V.22, V.22bis, V.32ter, V.32bis, V.34, K56flex, V.90

Fax Modulation Protocol

ITU-T V.17, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

Class I & II

Data Bus

PCMCIA

55301

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, A/

A, E, H, M, P, T, V, W, X, Z

&C, &F, &G, &R, &T, &W, &Y, &Z

Extended AT Commands

\A, \C, \G, \J, \K, \V, \X

%A, %G

Special Commands

"H, -J

S Registers

S0, S1, S2, S3, S4, S6, S7, S8, S9, S10, S11, S12, S18, S25, S30

 

Note: See MHI Help File for full command documentation.

Proprietary AT Command Set

AUTO-MODE DETECTION

Type:

Configuration

Format:

AT [cmds] Nn [cmds]

Description:

Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.

Command

Function

N0

Auto-mode detection disabled. Handshake begins at line speed designated by the S37 register and the B command.

í N1

Auto-mode detection enabled. Handshake begins at line speed designated by the S37 register and the B command. Fallback to lower speed if necessary unless in \N1 mode

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &Mn [cmds]

Description:

Selects communications mode

Command

Mode

í &M0

Asynchronous mode

&M4

Hayes autosynchronous mode

 

COMMUNICATION PROTOCOLS

Type:

Configuration

Format:

AT [cmds] Bn [cmds]

Description:

Selects the communication protocol for data calls

Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols.

Command

Protocol

B0

ITU-T V.22 at 1200bps or V.21 at 300bps

í B1

Bell 212A at 1200bps/Bell 103 at 300bps

B2

ITU-T V.23 at 75/1200bps originate; 1200/75bps answer

B3

ITU-T V.23 at 1200/75bps answer; 75/1200bps originate

CONFIGURATION PROFILES & CALL STATISTICS

Type:

Immediate

Format:

AT [cmds] &V [cmds]

Description:

Displays active and stored configuration profiles & statistics for last connection

Command

Function

&V0

Displays the active configuration, the two stored user profiles, and the first four phone numbers

&V1

Displays statistics for last connection

DATA SET READY (DSR)

Type:

Configuration

Format:

AT [cmds] &Sn [cmds]

Description:

Selects DSR options

Command

Function

í &S0

DSR forced high

&S1

DSR high only while modem is connected

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Command

Function

&D0

Modem does not respond to DTR

&D1

Modem goes to command mode on DTR toggle

í &D2

Modem goes to command mode and disconnects (hangs up) on DTR toggle;

Auto-Answer is disabled on low DTR.

&D3

Modem is initialized on DTR toggle

 

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Command

Function

DP

Pulse dialing enabled

DSn

Dial stored telephone number n

DT

Tone dialing enabled/Pulse dialing disabled

DW

Dialing resumed following dial tone detection

D,

Dialing paused for amount of time specified in S8 register

D!

Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.

D@

Wait for quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.

D$

Calling card "Bong" detection enabled

D;

Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Enables flow control options

Command

Function

&K0

Flow control disabled

í &K3

RTS/CTS flow control enabled

&K4

XON/XOFF flow control enabled

JACK TYPE

Type:

Configuration

Format:

AT [cmds] &Jn [cmds]

Description:

Command non-functional; for compatability purposes only

Command

Function

&J0

Send OK to DTE

&J1

Send OK to DTE

ON-LINE

Type:

Immediate

Format:

AT [cmds] On [cmds]

Description:

Controls on-line command (data transmission) state options.

Note: The O command must be placed at the end of the command string.

Command

Function

O0

On-line command mode with no retraining enabled

O1

On-line command mode with retraining enabled

O3-O14

Force modem to new rate defined by register S62

PULSE DIALING RATIO (INTERNATIONAL VERSION)

Type:

Configuration

Format:

AT [cmds] &Pn [cmds]

Description:

Selects pulse dial make/break ratio

Command

Function

&P0

39/61ms at 10pps (North America)

&P1

33/67ms at 10pps (Europe)

 

PULSE DIALING RATIO (JAPAN VERSION)

Type:

Configuration

Format:

AT [cmds] &Pn [cmds]

Description:

Selects pulse dial make/break ratio

Command

Function

&P0

33/67ms at 10pps (Europe)

&P1

33/67ms at 20pps

RESULT CODES

Type:

Configuration

Format:

AT [cmds] Qn [cmds]

Description:

Enables modem to send result codes to the DTE

Command

Function

í Q0

Result code sending enabled

Q1

Result code sending disabled

Q2

Dumb answer mode enabled

SPEAKER VOLUME

Type:

Configuration

Format:

AT [cmds] Ln [cmds]

Description:

Controls speaker volume

Command

Function

L0

Low volume setting

L1

Low volume setting

í L2

Medium volume setting

L3

Highest volume setting

V.32 - AUTO-RETRAIN

Type:

Configuration

Format:

AT [cmds] &Bn [cmds]

Description:

Controls auto-retrain function if poor line quality is detected

Command

Function

&B0

Auto-retrain disabled, modem hangs-up

í &B1

Auto-retrain enabled if line quality is poor. Hang-up if condition persists longer than threshold set by register S7

&B2

Modem tolerates any line

Extended AT Commands

COMPRESSION

Type:

Configuration

Format:

AT [cmds] %Cn [cmds]

Description:

Selects data compression

Command

Function

%C0

Data compression disabled

í %C1

MNP5 enabled

 

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \Nn [cmds]

Description:

Controls the type of connection the modem will operate in

Command

Function

\N0

Normal mode enabled

\N1

Direct mode enabled

\N2

Reliable mode enabled

í \N3

Auto-reliable mode enabled

\N4

V.42 reliable mode enabled

FLOW CONTROL TYPE

Type:

Configuration

Format:

AT [cmds] \Qn [cmds]

Description:

Sets type of flow control used by modem

Command

Function

\Q0

Flow control disabled

\Q1

Bi-directional XON/XOFF flow control enabled

\Q3

Bi-directional RTS/CTS flow control enabled

INACTIVITY TIMER

Type:

Configuration

Format:

AT [cmds] \Tn [cmds]

Range:

0-90

Unit:

1 minute

Description:

Sets the length of time that the modem does not receive information before it disconnects.

SPECIAL COMMANDS

DIALING MESSAGE CONTROL

Type:

Configuration

Format:

AT [cmds] %Mn [cmds]

Description:

Controls the output of dialing message when dialing a number stored in memory

Command

Function

í %M0

Dialing message disabled

%M1

Dialing message enabled

FIRMWARE VERSION

Type:

Immidiate

Format:

AT [cmds] -V [cmds]

Description:

Displays firmware version number

 

SERIAL PORT BAUD RATE

Type:

Configuration

Format:

AT [cmds] $SBn [cmds]

Description:

Sets the maximum allowable data exchange rate at serial port

Command

Function

$SB300

300bps

$SB1200

1200bps

$SB2400

2400bps

$SB4800

4800bps

$SB9600

9600bps

$SB19200

19.2Kbps

$SB38400

38.4Kbps

$SB57600

57.6Kbps

í $SB115200

115.2Kbps

S(STATUS) -REGISTERS

BACKSPACE CHARACTER

Type:

Register

Format

AT [cmds] S5=n [cmds]

Range:

0-127

Unit:

ASCII

Description:

Selects a character used for backspace <BS>

Note: A value greater than 32 will disable backspace

DCE LINE SPEED

Type:

Register

Format

AT [cmds] S37=n [cmds]

Description:

Sets the maximum allowable data exchange rate attempted during handshake process.

Command

Function

í S37=0

Speed of last connection

S37=3

300bps

S37=5

1200bps

S37=6

2400bps

S37=7

4800bps

S37=8

7200bps

S37=9

9600bps

S37=10

12.0Kbps

S37=11

14.4Kbps

S37=12

16.8Kbps

S37=13

19.2Kbps

S37=14

21.6Kbps

S37=15

24.0Kbps

S37=16

26.4Kbps

S37=17

28.8Kbps

S37=18

33.6Kbps

 

DTE RATE STATUS

Type:

Register

Format

AT [cmds] S62=n [cmds]

Description:

Sets the DTE rate status

Command

Function

S62=0

300bps

S62=1

600bps

S62=2

1200bps

S62=3

2400bps

S62=4

4800bps

S62=5

9600bps

S62=6

7200bps

S62=7

12.0Kbps

S62=8

14.4Kbps

S62=9

16.8Kbps

S62=10

19.2Kbps

S62=11

21.6Kbps

S62=12

24.0Kbps

S62=13

26.4Kbps

S62=14

28.8Kbps

S62=15

38.4Kbps

í S62=16

57.6Kbps

S62=17

115.2Kbps

DTE TRANSFER SPEED

Type:

Register

Format

AT [cmds] S72=n [cmds]

Description:

Sets the DTE speed during data transfer

Command

Function

í S72=0

Last auto-baud

S72=1

300bps

S72=2

600bps

S72=3

1200bps

S72=4

2400bps

S72=5

4800bps

S72=6

9600bps

S72=7

7200bps

S72=8

12.0Kbps

S72=9

14.4Kbps

S72=10

16.8Kbps

S72=11

19.2Kbps

S72=12

21.6Kbps

S72=13

24.0Kbps

S72=14

26.4Kbps

S72=15

28.8Kbps

S72=16

38.4Kbps

S72=17

57.6Kbps

S72=18

115.2Kbps

 

TRANSMISSION LEVEL (JAPAN)

Type

Register or Configuration

Format

AT [cmds] S64=n [cmds]

Range

9-20

Default

15

Unit

-1 dBm

Description

Sets the signal level for transmission (Japan version)

V.90 DOWNSTREAM DATA RATE

Type:

Register

Format

AT [cmds] S38=n [cmds]

Description:

Sets the maximum allowable V.90 downstream rate attempted during handshake process.

Command

Function

S38=0

56K disabled

S38=1

56K automatic speed select

S38=2

29.3Kbps

S38=3

30.6Kbps

S38=4

32.0Kbps

S38=5

33.3Kbps

S38=6

34.6Kbps

S38=7

36.0Kbps

S38=8

37.3Kbps

S38=9

38.6Kbps

S38=10

40.0Kbps

S38=11

41.3Kbps

S38=12

42.6Kbps

S38=13

44.0Kbps

S38=14

45.3Kbps

S38=15

46.6Kbps

S38=16

48.0Kbps

S38=17

49.3Kbps

S38=18

50.6Kbps

S38=19

52.0Kbps

S38=20

53.3Kbps

S38=21

54.6Kbps

S38=22

56.0Kbps

V.90 MODE SELECTION

Type:

Register

Format:

AT [cmds] S109=n [cmds]

Description:

Selects modem operating mode

Command

Function

í S109=0

V.90 disabled

S109=1

K56flex or V.90 mode enabled

S109=2

V.90 mode enabled; K56flex disabled