BEST DATA PRODUCTS, INC.

SMART ONE 2834F, SMART ONE 2834V, SMART ONE 2834VP

Card Type

Modem (asynchronous)

Chipset

Unidentified

I/O Options

Voice (except on Smart One 2834F)

Maximum Data Rate

28.8Kbps

Maximum Fax Rate

14.4Kbps

Data Bus

8-bit ISA

Fax Class

Class I & II

Data Modulation

Bell 103A/212A

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34

Rockwell V.FC

Fax Modulation

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP5, MNP10EC, V.42, V.42bis

CONNECTIONS

Function

Label

Function

Label

Line out

CN1

Line in

CN2

INTERRUPT SELECTION

Setting

SW1/1

SW1/2

SW1/3

SW1/4

í IRQ3

On

Off

Off

Off

IRQ4

Off

On

Off

Off

IRQ5

Off

Off

On

Off

IRQ7

Off

Off

Off

On

SERIAL PORT ADDRESS SELECTION

Setting

SW1/5

SW1/6

3F8h (COM1:)

On

On

í 2F8h (COM2:)

On

Off

3E8h (COM3:)

Off

On

2E8h (COM4:)

Off

Off

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

&C, &D, &F, &G, &K, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z

Extended AT Commands

\A, \B, \G, \K, \N

%C, %E, %L, %Q

Special AT Commands

#CID, +MS

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26

S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95

Note: See MHI documentation for complete information.

UNIDENTIFIED COMMANDS

Command

Default

S37

0

S201

Unidentified

Proprietary AT Command Set

DISPLAY INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested about the modem.

Command

Function

I0

Displays product identification code.

I1

Displays ROM checksum.

I3

Displays firmware model, revision, and interface.

I5

Displays country code.

I6

Displays data pump model and revision.

I7

Displays the DAA code.

MNP10 POWER LEVEL ADJUSTMENT

Type:

Configuration

Format:

AT [cmds] )Mn [cmds]

Description:

Controls automatic transmit power level adjustment during MNP 10 link negotiation.

Command

Function

)M0

Power level adjustment disabled.

)M1

Power level adjustment enabled.

)M2

Power level adjustment enabled; S40 bit 2 and S201 bit 6 are reset to their default settings.

MNP10EC MODE

Type:

Configuration

Format:

AT [cmds] -SEC=n [cmds]

Description:

Selects whether the modem will attempt to use MNP10EC mode during the handshaking sequence.

Command

Function

-SEC=0

MNP10EC handshaking disabled unless a V.34 connection is attempted via a cellular line.

í -SEC=1

MNP10EC handshaking enabled.