CONTROL CONCEPTS, INC.

16-BIT SCSI, IDE, FLOPPY, SERIAL & PARALLEL COMBINATION BOARD (VERSION 2)

Data bus:

16-bit, ISA

Size:

Three-quarter-length, full-height card

Hard drive supported:

IDE (AT) Interface drive, SCSI drives (2)

Floppy drives supported:

Two 360KB, 720KB, 1.2MB, 1.44MB, or 2.88 drives

CONNECTIONS

Function

Location

Floppy drive interface 1

CN1

Floppy drive interface 2

CN2

Serial port 4

CN3

Serial port 3

CN4

Serial port 2

CN5

Serial port 1

CN6

Parallel port 1

CN7

IDE interface

CN8

Parallel port 2

CN9

SCSI interface

CN10

SCSI interface 2

CN11

USER CONFIGURABLE SETTINGS

Function

Location

Setting

»

2.88MB Floppy drive mode disabled

JB1/A

Open

 

2.88MB Floppy drive mode enabled (w/pin 33 as 2nd enable line)

JB1/A

Pins 2 & 3

 

2.88MB Floppy drive mode enabled (standard enabling)

JB1/A

Pins 1 & 2

»

Factory configured - do not alter

JB3/A

N/A

»

Factory configured - do not alter

JB3/B

N/A

»

Factory configured - do not alter

JB3/C

N/A

»

Factory configured - do not alter

JB3/D

N/A

»

No termination power to external SCSI interface

JB6/A

Open

 

5V termination power to external SCSI interface

JB6/A

Closed

»

Factory configured - do not alter

JB6/D

N/A

»

I/O Address 330h - 33Fh

JB6/E

Open

 

I/O Address 230h - 23Fh

JB6/E

Closed

»

SCSI protocol asynchronous

JB6/F

Open

 

SCSI protocol synchronous

JB6/F

Closed

»

SCSI device ID 7

JB6/G

Open

 

SCSI device ID 6

JB6/G

Closed

»

SCSI parity enabled

JB6/H

Open

 

SCSI parity disabled

JB6/H

Closed

»

Factory configured - do not alter

JB6/K

N/A

»

ROM enabled

JB6/L

Closed

 

ROM disabled

JB6/L

Open

»

Factory configured - do not alter

JB6/M

N/A

»

Zero wait state disabled

JB6/N

Open

 

Zero wait state enabled

JB6/N

Closed

»

Factory configured - do not alter

JB/7

N/A

IDE CONFIGURATION

Setting

JB1/B

JB1/C

»

IDE interface enabled (address 1F0h - 1F7h)

Pins 2 & 3 closed

Pins 1 & 2 closed

 

IDE interface enabled (address 170h - 177h)

Pins 1 & 2 closed

Pins 1 & 2 closed

 

IDE interface disabled

Pins 2 & 3 closed

Pins 2 & 3 closed

 

Reserved for future use

Pins 1 & 2 closed

Pins 1 & 2 closed

FLOPPY DRIVE CONFIGURATION

Setting

JB1/D

JB1/E

»

Floppy drive interface enabled (address 3F0h - 3F7h)

Pins 2 & 3 closed

Pins 1 & 2 closed

 

Floppy drive interface enabled (address 370h - 377h)

Pins 1 & 2 closed

Pins 1 & 2 closed

 

Floppy drive interface disabled

Pins 2 & 3 closed

Pins 2 & 3 closed

 

Reserved for future use

Pins 1 & 2 closed

Pins 2 & 3 closed

PRIMARY PARALLEL PORT CONFIGURATION

Setting

JB1/F

JB1/G

»

Unidirectional mode enabled

Pins 2 & 3 closed

Pins 2 & 3 closed

 

Bi-directional mode enabled

Pins 1 & 2 closed

Pins 2 & 3 closed

 

Reserved for future use

Pins 2 & 3 closed

Pins 1 & 2 closed

 

Reserved for future use

Pins 1 & 2 closed

Pins 1 & 2 closed

PRIMARY PARALLEL PORT ADDRESS SELECT

LPT

JB1/H

JB1/I

»

1

Pins 2 & 3 closed

Pins 1 & 2 closed

 

2

Pins 1 & 2 closed

Pins 1 & 2 closed

 

3

Pins 1 & 2 closed

Pins 2 & 3 closed

 

Disabled

Pins 2 & 3 closed

Pins 2 & 3 closed

PRIMARY PARALLEL PORT INTERRUPT SELECT

IRQ

JB4/E

»

IRQ7

Pins 1 & 2 closed

 

IRQ5

Pins 2 & 3 closed

SECOND PARALLEL PORT CONFIGURATION

Setting

JB2/A

JB2/B

»

Unidirectional mode enabled

Pins 2 & 3 closed

Pins 2 & 3 closed

 

Bi-directional mode enabled

Pins 1 & 2 closed

Pins 2 & 3 closed

 

Reserved for future use

Pins 2 & 3 closed

Pins 1 & 2 closed

 

Reserved for future use

Pins 1 & 2 closed

Pins 1 & 2 closed

SECOND PARALLEL PORT ADDRESS SELECT

LPT

JB2/C

JB2/D

»

LPT2

Pins 1 & 2 closed

Pins 1 & 2 closed

 

LPT1

Pins 2 & 3 closed

Pins 1 & 2 closed

 

LPT3

Pins 1 & 2 closed

Pins 2 & 3 closed

 

Disabled

Pins 2 & 3 closed

Pins 2 & 3 closed

SECOND PARALLEL PORT INTERRUPT SELECT

IRQ

JB4/F

»

IRQ5

Pins 2 & 3 closed

 

IRQ7

Pins 1 & 2 closed

PRIMARY SERIAL PORT ADDRESS SELECT

Port 1 (CN6)

JB1/L

JB1/M

»

COM1

Pins 1 & 2 closed

Pins 1 & 2 closed

 

COM2

Pins 2 & 3 closed

Pins 1 & 2 closed

 

COM3

Pins 1 & 2 closed

Pins 2 & 3 closed

 

Disabled

Pins 2 & 3 closed

Pins 2 & 3 closed

PRIMARY SERIAL PORT INTERRUPT SELECT

IRQ

JB4/A

»

IRQ4

Pins 1 & 2 closed

 

IRQ3

Pins 2 & 3 closed

SECOND SERIAL PORT ADDRESS SELECT

Port 2 (CN5)

JB1/J

JB1/K

»

COM2

Pins 1 & 2 closed

Pins 1 & 2 closed

 

COM1

Pins 2 & 3 closed

Pins 1 & 2 closed

 

COM4

Pins 1 & 2 closed

Pins 2 & 3 closed

 

Disabled

Pins 2 & 3 closed

Pins 2 & 3 closed

SECOND SERIAL PORT INTERRUPT SELECT

IRQ

JB4/B

»

IRQ3

Pins 2 & 3 closed

 

IRQ4

Pins 1 & 2 closed

THIRD SERIAL PORT ADDRESS SELECT

Port 3 (CN4)

JB2/G

JB2/H

»

COM3

Pins 1 & 2 closed

Pins 2 & 3 closed

 

COM1

Pins 1 & 2 closed

Pins 1 & 2 closed

 

COM2

Pins 2 & 3 closed

Pins 1 & 2 closed

 

Disabled

Pins 2 & 3 closed

Pins 2 & 3 closed

THIRD SERIAL PORT INTERRUPT SELECT

IRQ

JB4/C

»

IRQ4

Pins 1 & 2 closed

 

IRQ3

Pins 2 & 3 closed

FOURTH SERIAL PORT ADDRESS SELECT

Port 4 (CN3)

JB2/E

JB2/F

»

COM4

Pins 1 & 2 closed

Pins 2 & 3 closed

 

COM1

Pins 2 & 3 closed

Pins 1 & 2 closed

 

COM2

Pins 1 & 2 closed

Pins 1 & 2 closed

 

Disabled

Pins 2 & 3 closed

Pins 2 & 3 closed

FOURTH SERIAL PORT INTERRUPT SELECT

IRQ

JB4/D

»

IRQ3

Pins 2 & 3 closed

 

IRQ4

Pins 1 & 2 closed

INTERRUPT SELECT

IRQ

JB6/I

JB6/J

JB3/E

JB3/F

JB3/G

JB3/H

IRQ11

Open

Open

Open

Open

Closed

Open

IRQ10

Closed

Open

Open

Open

Open

Closed

IRQ12

Closed

Closed

Open

Closed

Open

Open

IRQ15

Open

Closed

Closed

Open

Open

Open

BASE MEMORY ADDRESS SELECT

Address

JB6/B

JB6/C

»

C8000h

Open

Open

 

CC000h

Open

Closed

 

D8000h

Closed

Open

 

DC000h

Closed

Closed

LED SOURCE CONFIGURATION

Setting

JB5

»

LED functions with IDE activity

Pins 2 & 3 closed

 

LED functions with SCSI activity

Pins 1 & 2 closed

 

LED funtions with both IDE and SCSI activity

Pins 4 & 5 closed